Air Ring Gauge Range 1.5 – 150 mm
FEATURES:
  • Two Jet Air Ring gauge to check outside diameter, taper & ovality
  • Three jet Air Ring gauge for detecting tri-lobed effect for diameter above 6 mm only
  • Can be supplied with tungsten carbide sleeve on request for checking hardened job
  • Can be supplied with multiple jets

 

air-ring-gauge-range-1-5-150-mm_01 air-ring-gauge-range-1-5-150-mm_02

 

Special Application
air-ring-gauge-range-1-5-150-mm_03
air-ring-gauge-range-1-5-150-mm_04
air-ring-gauge-range-1-5-150-mm_05
air-ring-gauge-range-1-5-150-mm_06

 

Data Sheet

range-1-5-150-mm_07

Ø D mm A T B E F MIN RANGE MAX RANGE
2.0 – 3.0 35.0 9.0 4.5 6.6 2.5 ±0.005 80% OF SCALE
3.0 – 6.0 35.0 9.0 4.5 6.6 2.5 ±0.005 80% OF SCALE

 

  • Supplied hand held as standard
  • Supplied on MOD 2A / ClearLine only
  • Supplied with 2 jets as standard
  • Not supplied in offset design

range-1-5-150-mm_08

Ø D mm A T B B1 E (OFFSET) MOD 1A/ CL F (CENTRAL) MOD 1A/ CL MIN RANGE MAX RANGE
6.0-20.0 60.0 20.0 10.0 4.5 6.5/5.5 4.5/3.5 ±0.005 80% OF SCALE
20.0-40.0 86.0 20.0 10.0 4.5 6.5/5.5 4.5/3.5 ±0.010 80% OF SCALE
40.0-65.0 120.0 20.0 10.0 4.5 6.5/5.5 4.5/3.5 ±0.015 80% OF SCALE
65.0-100.0 154.0 20.0 10.0 4.5 6.5/5.5 4.5/3.5 ±0.020 80% OF SCALE
100.0-120.0 184.0 20.0 10.0 4.5 6.5/5.5 4.5/3.5 ±0.020 80% OF SCALE
120.0-150.0 225.0 20.0 10.0 4.5 6.5/5.5 4.5/3.5 ±0.020 80% OF SCALE

 

  • Supplied unit mounted as standard
  • As a special case, air ring can be supplied on MOD-2A up to dia. 50 mm only, to suit super blind and less land

 

General Details
  • Air ring gauge for 0.0005 mm least count are given up to Ø 50 mm only
  • Each air ring gauge requires two setting masters to set the air ring on the read-out unit. The difference between the high and low setting masters supplied covers the component tolerance or the maximum range mentioned in the above table, whichever is lower
  • The minimum gauging land “E” and “F” mentioned above, is excluding chamfer distance and fillet radius
  • For special blind shafts (super blind- ‘E’ less than mentioned in the above chart) or any other special requirement (3 Jet design to check lobing), please send the component drawing and ask for a quote

range-1-5-150-mm_09

Abbreviations:
  • MOD 1A = PFL Air Gauge Unit Module 1A
  • MOD 2A = PFL Air Gauge Unit Module 2A
  • CL = ClearLine air gauge unit
Important rule in air gauging

Lesser the clearance, higher the accuracy and vice versa.