These ABSOLUTE Digimatic bore gages are exclusively designed for inside diameter measurement. Up to four extension rods (250mm or 500mm) can be used for measuring at the bottom of a hole 2m deep. ABS (ABSOLUTE) type bore gages are not subject to overspeed error. The display and grip can be rotated up to 320 degrees and […]
Capable of ID (inside diameter) measurement close to the bottom of a hole. Carbide contact point ensuring high durability and wear resistance. Grip is large and hollow to reduce effect of body heat on high-accuracy measurements. Alternative indicators may be used in place of those recommended*. * Some indicators and protection covers cannot be used with these […]
Micrometer head is attached to the anvil for accurate dimensional setting. Longer plunger stroke with no affect on accuracy. Carbide is used for the contact point ensuring high durability and wear resistance. This model reduces the influence of heat from the operator’s hand by 50% by increasing the grip size and making the grip hollow-structured, thereby […]
Compact and lightweight due to the short length below the grip. Longer plunger stroke with no affect on accuracy. Carbide contact point ensuring high durability and wear resistance. This model reduces the influence of heat from the operator’s hand by 50% by increasing the grip size and making the grip hollow-structured, thereby retaining high-accuracy measurement. Alternative indicators […]
Longer plunger stroke with no affect on accuracy. Carbide is used for the contact point ensuring high durability and wear resistance. This model reduces the influence of heat from the operator’s hand by 50% by increasing the grip size and making the grip hollow-structured, thereby retaining high-accuracy measurement. Alternative indicators may be used in place […]
Alternative indicators may be used in place of those recommended*. Some indicators and protection covers cannot be used with these bore gages. Contact a Mitutoyo sales office if considering the use of dial or digimatic indicators other than the recommended models. Setting Rings are available to aid in accurately setting a gage before making a measurement. (For details, […]
Wide range of inside diameter measurements possible by combining one or more interchangeable rods. Each interchangeable rod is marked with its measuring range. For models supplied with more than one interchangeable rod, the full measuring range is achieved by combining spacing collars with the rods. Both micrometer head and rods are satinchrome finished throughout. The sleeve is rotated […]
Carbide measuring faces. Equipped with a constant measuring-force device. Setting ring (nominal size below 300mm), CERA Inside Micro Checker (more than 50mm), and Gauge Block accessory set are provided as a reference gage for datum adjustment (refer to page C-47, C-26, and E-17 – E20 for details). SPECIFICATIONS Metric Order No. Range Resolution Accuracy* Mass Digimatic (LCD) […]
Wide range of inside diameter measurements possible by combining extension pipes and anvils with the micrometer head. Carbide measuring faces are available. The sleeve is rotated to adjust the index line position when setting to a length An inside length standard is required for accurately setting the micrometer. Order No. 339-101/301/302/102/303/304 features: IP65 (water-proof) protection […]
Wide range of inside measurements possible by combining extension rods and anvils with the micrometer head. Two types of measuring faces are available; with or without carbide tip. (No. 337- 101/301/302/102/303/304 only available with carbide ) The sleeve is rotated to adjust the index line position when setting to a length standard. An inside length […]
Standard single rod type inside Carbide measuring The sleeve is rotated to adjust the index line position when setting to a length Setting ring (nominal size below 300mm), CERA Inside Micro Checker, and Gauge Block accessory set are provided as a reference gage for datum adjustment (refer to page C-47, C-26, and E-17 – E20 […]
A snap-type digital display, inside-diameter measuring instrument allows quick and easy measurement with lever operation. Titanium-coated measuring pins provide excellent durability and impact resistance and allow the instrument to measure right to the bottom of a blind hole. Three-Point contact measuring head enables highly repeatable measurement data to be obtained. The ABSOLUTE linear encoder eliminates overspeed errors. GO/NO-GO […]
Hardened tool-steel anvils (instead of titanium-coated carbide) for a more economically priced tool. Same accuracy as the titanium-coated Holtest models. For details of setting rings, refer to page C-47 Constant-force device allows repeatable measurement. Can measure deep holes using an Extension Rod (optional). Range (mm) L3 (mm) L5 (mm) 12 – 20 2.6 or below […]
Titanium-coated measuring pins on the three- point type (over 6mm range models) provide excellent durability and impact resistance and allow the instrument to measure right to the bottom of a blind Three-point bore micrometer with measuring range 6mm or longer allows stable measurement through automatic Can measure deep holes using an Extension rod (optional) which […]
v Three-point internal micrometer with large LCD readout. (Character height 7.4mm) Titanium-coated measuring pins provide excellent durability and impact resistance and allow the instrument to measure right to the bottom of a blind One SR44 battery is required and battery life is 1.2 years under normal use. ABSolute and INCremental measurement modes allow highly efficient […]
A spring-loaded plunger expands within a bore (or groove) and is locked in place, allowing measurement of diameter (or width) with an outside micrometer after extraction. SPECIFICATIONS Metric Order No. Range 6-gage Set 155-905 8 – 150mm Gages included 155-127 8 – 12.7mm 155-128 12.7 – 19mm 155-129 19 – 32mm 155-130 32 – 54mm […]
Extra long for gaging deep and shallow holes, slots, and similar workpiece features. Two sprung leaves are fully expanded inside a feature so that its size can be measured with an outside micrometer after extraction. SPECIFICATIONS Metric Order No. Range 4-gage Set 154-902 3 – 13mm Gages included 154-101 3 – 5mm 154-102 5 […]
Maximum wear resistance due to carbide ball anvils Constant measuring force due to built-in spring, eliminating user influence Anvils, measuring heads, holder, spacer (intermediate piece) and depth extensions form a very comprehensive modular system which can rapidly be converted to measure further gear sizes When ordering please state the required ball diameter Technical data Order […]
Measuring head consists of a carbide tipped moving anvil and an interchangeable stationary anvil with a carbide ball Transmission lever system transfers movement of movable anvil to indicating instrument The broad centering bridge ensures automatic centering in the bore Resistant to temperature because the shank and transfer rod are made of heat resistant Invar steel Highly resistant […]
Measuring head consists of a carbide tipped moving anvil and an interchangeable stationary anvil with a carbide ball Transmission lever system transfers movement of movable anvil to indicating instrument The broad centering bridge ensures automatic centering in the bore Resistant to temperature bacause the shank and transfer rod are made of heat resistant Invar steel Highly resistant […]
Maximum wear resistance due to hard chrome plating Constant measuring force as a result of built-in spring, eliminating user influence Highly versatile – Each gage covers a broad range – Quickly and easily adjustable to any size and type of measuring application (within the limits) Extensive modular system is composed of measuring probe, holder, depth extensions, […]
MICROMAR 44 AK MEASURING HEAD Self-centering measuring head consists of 3 laterally positioned anvils, each are offset at intervals of 120° Anvils from 12 mm are carbide tipped From 12 mm the anvils can be used to measure the bottom of a bore From 40 mm all measuring heads are made from aluminium to reduce […]
MICROMAR 844 A SELF-CENTERING INSIDE MEASURING PISTOL Threaded connection for changing the measuring head Self-centering measuring head consists of 3 laterally positioned anvils, each are offset at intervals of 120° Anvils from 12 mm are carbide tipped From 12 mm the anvils can be used to measure the bottom of a bore From 40 mm […]
MICROMAR 44 EWR DIGITAL SELF-CENTERING INSIDE MICROMETER Threaded connection for changing the measuring head Self-centering measuring head consists of 3 laterally positioned anvils, each are offset at intervals of 120° Anvils from 12 mm are carbide tipped From 12 mm the anvils can be used to measure the bottom of a bore From 40 mm […]
Operating and display units with satin chrome finish Rigid, lightweight tubular construction Stainless spindle is hardened throughout and ground Locking device Carbide tipped spherical measuring faces Interchangeable extension 44 Cv contains cylindrical gage rods that are spring mounted in protective sleeves for the extension of the measuring range Protection sleeves have a satin chrome finish […]
Operating and display units with satin chrome finish Measuring head and end piece with mounting bore for interchangeable anvils Rigid, lightweight tubular construction Stainless spindle is hardened throughout and ground Locking device Interchangeable extension 44 Cv contains cylindrical gage rods that are spring mounted in protective sleeves for the extension of the measuring range Protection […]
Operating and display units with satin chrome finish Rigid, lightweight tubular construction Stainless spindle is hardened throughout and ground Locking device Carbide tipped spherical measuring faces Interchangeable extension 44 Cv contains cylindrical gage rods that are spring mounted in protective sleeves for the extension of the measuring range Protection sleeves have a satin chrome finish […]
Operating and display units with satin chrome finish Rigid, lightweight tubular construction Stainless spindle is hardened throughout and ground Measuring faces spherically lapped, one measuring face adjustable Measuring range of 100-125 mm with heat insulators and a locking device case Technical Data Order no. Measuring range mm Graduation value mm Error limit µm Spindle thread […]
Excessive web deflection is dangerous for the engine. The cause may be faulty or damaged crankshaft, damaged bearing, poor bearing alignment, excessive bearing clearance or slackness, faulty flanging to transmission, flywheel or Vee Belt pulley, etc. FEATURES: Every gauge carries a calibration certificate giving actual values Crankshaft Gauge measures the Web deflection of a crankshaft […]
Dial Bore Gauge Range: 10 – 18mm FEATURES: Every gauge carries a calibration certificate giving actual values Measures small bores from 10 mm to 18 mm High wear resistance due to carbide-tipped fixed and moving anvils Wide bridge ensures automatic centering in the bore Self-centralizing feature of this bore gauge ensures that measurement can be […]