Baker Gauges MicrometerBAKER GAUGES MICROMETER

Latest Promotions

Some new offers for you

Products

Few products of our basket

AUTHOR RATE
B (BALL) BLOCKS with clamp

B (BALL) BLOCKS with clamp Used for Checking of heavy round & cylindrical jobs. Supplied in perfectly matched pair having accuracy 0.005mm. Four hard steel balls on top face provides self-aligning, hard wearing, accurate support. Total contact area as compared to V block is more. Ball wearing is even , so accuracy doesn’t get affected. […]

AUTHOR RATE
Mitutoyo-500 Series – with exclusive ABSOLUTE Encoder Technology-ABSOLUTE Digimatic Caliper

ABSOLUTE electromagnetic induction linear encoder system is introduced (except for 0 – 300mm/0 – 12″ models). New ergonomic design with finger rest. The ZERO/ABS button allows the display to be Zero-Set at any slider position along the scale for comparison measurements. This button will also allow return to the absolute (ABS) mode and display of the true […]

AUTHOR RATEUSERS RATE (0)
NON SPARKING TOOLS

TAPARIA Non-sparking safety tools • Provide protection against fire and explosions. • Are non-magnetic and corrosion-resistant. • Protect workmen and plant from fire related accidents. • Approved by Govt. recognized laboratory in India. • Made of beryllium coper and alluminium bronze. NON SPARKING TOOLS

AUTHOR RATEUSERS RATE (0)
360° SWIVEL VIDEOSCOPE CODE – ISV-3000D

  Check the PDF

AUTHOR RATE
MILLIMESS MAXΜM III DISPLAY UNIT

Large, high contrast digital, analog and fan display for better readability while testing flatness and concentricity as well as for searching the reversal point in bores Interchangeable dials Inductive absolute measuring system Metal cast housing with robust buttons Technical data Order no. Product type Measuring range mm Standard IP protection category 2033001 Maxµm III Depending […]

AUTHOR RATE
Mitutoyo-SERIES 543-ABSOLUTE Solar-Powered Digimatic Indicator ID-SS

Solar powered An environmentally friendly measuring instrument that does not require batteries, eliminating the hassle and cost of battery replacement. Can operate under minimum light conditions of 40 lux—lower than the level in a warehouse. Built-in recharger The large-capacity built-in reservoir capacitor allows you to use the indicator for long periods of time under light conditions below the […]

M.A.Ford Diamond Coated Routers 239 Dealer
AUTHOR RATEUSERS RATE (0)
DIAMOND COATED ROUTERS

  To know specifications,Check the PDF.

AUTHOR RATE
Mitutoyo-SERIES 107-Indicator Type Micrometers

Designed to mount a dial indicator for direct GO/±NG judgment on mass-produced parts. Anvil retracting trigger for quick measurement. Various kinds of indicators*1 are selectable depending on the measurement type (accuracy required, measuring range, etc.). Measuring faces: Carbide Anvil stroke: 3mm SPECIFICATIONS Metric Order No. Range Accuracy 107-201 0 – 25mm   ±2µm 107-202 25 – 50mm 107-203 […]

AUTHOR RATEUSERS RATE (0)
DIGITAL THICKNESS GAUGE

DIGITAL THICKNESS GAGE CODE – 2871 Ceramic spindle tip and anvil Buttons: on/off, zero, mm/inch Battery CR2032, automatic power off Data output Optional accessory: data output system   Code Range Resolution Accuracy 2871-10 0-10mm/0-0.4″ 0.01mm/0.0005″ ±0.02mm 2871-101 0-10mm/0-0.4″ 0.001mm/0.00005″ ±0.005mm Check the PDF   DIGITAL THICKNESS GAGE CODE – 2867 Ceramic spindle tip and anvil […]

AUTHOR RATE
MARCAL 18 N – WORKSHOP CALIPERS, VERNIER

MARCAL 18 N WORKSHOP CALIPERS Vernier and main scale have a satin chrome finish for glare free reading Locking screw above Rounded measuring blades for inside measurements Measuring surfaces made of steel Slide and beam made of hardened stainless steel Raised guideway for the protection of the scale up to 1000 mm delivered with a […]

AUTHOR RATEUSERS RATE (0)
DIGITAL LEVEL CODE – 4910

With transverse and longitudinal vials Used as level and protractor Aluminum frame Magnetic bottom The sea level is permanently set inside the chip, zero setting is not needed when batteries are replaced Buttons: ON/OFF, absolute and incremental measurement, keep the reading, buzzer alarm, unit (mm/m, %, in/ft) conversion, backlight The display flips over when the […]

AUTHOR RATE
HARDENED & GROUND V BLOCKS

Used for supporting of round and square jobs during Light machining. Grinding, Drilling & Inspection. Accuracy for Flatness, Squareness and parallelism within ±0.003mm. Hardness 60±2 Rc. Supplied in perfect matched pair. Supplied with clamp. Can also be used for end face. side face and right angle Grinding   Sr. No. Art No. Size (MM) Range (MM) […]

AUTHOR RATEUSERS RATE (0)
DIAL SNAP GAGE CODE – 3334

Go/No-Go judgement for mass production Dial indicator: range ±0.04mm, graduation 0.001mm, accuracy 0.001mm IP54 dust/waterproof Measuring force: 5-10N Carbide measuring faces Supplied with setting standards (except 0-25mm)   Code Range L D 3334-25 0-25mm 28.5 25 3334-50 25-50mm 53.5 35 3334-75 50-75mm 78.5 47.5 3334-100 75-100mm 103.5 60 Check the PDF

AUTHOR RATE
MILLING MACHINE VICE

COOE NO. 803 SWIVEL BASE CODE NO. 803S STEEL BODY SWIVEL BASE CODE NO. 803P PLAIN BASE CODE NO. 803PS STEEL BODY PLAIN BASE SIZE IN INCHES 2 3 4 5 6 8 10 12 Width of jaws in mm 50 75 100 125 150  200 250 300 Opening of jaws in mm 50 […]

AUTHOR RATE
Mitutoyo-SERIES 167-Setting Standards for Outside Micrometers

Used for adjusting the reference point of the outside micrometer. SPECIFICATIONS and DIMENSIONS Metric Order No. Length  (L) Tolerance   Diameter  (D) 167-101 25mm ±1.5µm 18   6.35mm 167-102 50mm ±2.0µm 40 167-103 75mm ±2.5µm Inch Order No. Length  (L) Tolerance   Diameter  (D) 167-141 1″ ±.00005″ 18   .25″ 167-142 2″ ±.0001″ 40 167-143 […]

AUTHOR RATEUSERS RATE (0)
BAKER TUBE TYPE MICROMETER

FEATURES: Spindle made from stainless steel for rust prevention Measuring faces: hardened steel available in two types: T1 – one end spherical T2 – both ends spherical An in-built ratchet in the thimble Zero setting once done cannot be easily tampered with Sharp laser marking for better visibility & durability Heat insulating grip plates cover […]

AUTHOR RATE
Mitutoyo-SERIES 149 – Small Standard Type with Carbide-Tipped Spindle-Micrometer Heads

Carbide-tipped spindle provides high abrasion resistance. DIMENSIONS SPECIFICATIONS Metric Order No. Range Accuracy Stem dia. Stem Spindle end Graduation features 149-132           0 – 15mm           ±2µm           9.5mm Plain   Flat (carbide tip)     Standard 149-131 W/ clamp nut 149-183 Plain* […]

AUTHOR RATE
MARCAL 18 EWR – DIGITAL WORKSHOP CALIPER, IP 65, DATA INTERFACE

Digital workshop caliper, IP 65, Data interface, with blades Measuring blades for outside measurements High contrast analog display Locking screw above Rounded measuring blades for inside measurements Slide and beam made of hardened stainless steel Immediate measurements due to the Reference System Raised guideways for the protection of the scale Excellent resistance against dust, coolants […]

AUTHOR RATE
MARCAL 16 EWR-H DIGITAL CALIPER FOR SPECIAL APPLICATIONS

High contrast analog display Locking screw above Lapped guideway Measuring blade for inside measurements Slide and beam made of hardened stainless steel Step measuring function Immediate measurements due to the Reference System Raised guideway for the protection of the scale Excellent resistance against dust, coolants and lubricants Dirt wipers are integrated in the slide USB […]

AUTHOR RATE
MARCAL 16 EWR-SA DIGITAL CALIPER FOR SPECIAL APPLICATIONS

High contrast analog display Locking screw above Lapped guideway Slide and beam made of hardened stainless steel Immediate measurements due to the Reference System Raised guideway for the protection of the scale Excellent resistance against dust, coolants and lubricants Dirt wipers are integrated in the slide USB Opto RS232C Digimatic IP 67 batteryins truction manual […]

AUTHOR RATEUSERS RATE (0)
SURFACE PLATE WITH BENCH CENTRE

Surface Plate with Bench Center is the dual combination of surface plate and bench center, this combined feature make them extremely useful inspection equipment in engineering industry.   Size of Plate mm Centre Distance mm Centre Height mm 750 X 600 400 125 1000 X 630 600 160 1000 X 1000 600 200 1000 X 1600 […]

AUTHOR RATE
Mitutoyo-SERIES 148 — Short Thimble with Choice of Diameter-Micrometer Heads

Short body design maintains measuring range for limited space applications. Available in three thimble diameters to provide ease-of-reading options. DIMENSIONS Technical Data Graduation: 0.01mm or .001” Spindle pitch: 0.5mm or .025”

AUTHOR RATEUSERS RATE (0)
BORESCOPE WITH MIRROR (RIGID) CODE – ISV-HM6051

Front view, side view with mirror Dust/waterproof level : IP67 Lens can be uses in the liquid with temperature – 10°C – 80°C LED light source is needed Check the PDF

AUTHOR RATE
MARAMETER 838 EI ELECTRONIC GAGE FOR INTERNAL MEASUREMENT

High contrast analog and digital LCD Tolerance displayed with 2 LEDs               Technical data Order no. Product type Measuring range mm Graduation value mm Repeatability mm Error limit (mm) Measuring force (N) Measuring depth mm Measuring contact ball diameter mm Length of moving measuring contact Groove depth Groove width […]

AUTHOR RATEUSERS RATE (0)
DIGITAL SHORE DUROMETER CODE – ISH-DSD

According to ISO868, ISO7619, ASTM D 2240 Average and peak (max.) mode Dwell time is adjustable Low and high limits with judgement 500 memories Wireless connection to printer Handhold use or work with test stand (code ISH-DS-STAND) Automatic power off Check the PDF

AUTHOR RATE
Digital Gauging Probes

Orbit® Digital Measurement Network Ultra flexible network for Gauging and Linear Measurement. Wide range of Solartron Sensors Interface to 3rd Party sensors Contact and Non Contact Measurements High speed measurements Interfaces to Excel® Orbit® Library – based on Microsoft .NET Framework. Windows® 10, 8.1, 7 and XP in both 64 bit and 32 bit Conventional […]

AUTHOR RATE
Straddle Knurling tool Holder

RAPID TOOL SERIES  S201 MACHINE TYPE: Troub,Mini Lathe, Sliding head, Autolathe, lathe, CNC machine SUITABLE METHOD: Plunge knurling, Feed knurling FEATURES: Form knurling without swart removal Minimises lateral pressure on workpiece Less strain on machine and workpiece Suitable for machining small and delicate parts Form knurling of thin-walled work pieces POSSIBLE KNURLING PROFILE: TOOL CODING SYSTEM 

AUTHOR RATEUSERS RATE (0)
SHORE DUROMETER CODE – ISH-S30D

According to ISO868, ISO7619, ASTM D 2240 With peak value indicator Handhold use or work with test stand (code ISH-OS2) Check the PDF

Unoair Speciality Tools / Tools for Body Shope Dealer
AUTHOR RATEUSERS RATE (0)
SPECIALITY TOOLS / TOOLS FOR BODY SHOPE

B-12 B-13 B-14 B-21 B-26 B-27 B-72 Air Nipper (For PCB Lead cutting) B-73Air Nipper (For PCB Lead cutting) B-54 Spot Drill Machine B-40 S-001 Suction Cupset (Metal Body) S-002 Suction Cup S-17 B-36 SB-74k Spark Plug Cleaner Kit   Technical Specification Model No Cutting Capacity (mm) Stroke Length (mm) BPM Air Consumption (cfm) Steel […]

AUTHOR RATE
MICROMAR 40 A MICROMETER

Operating and display units with satin chrome finish Hard lacquered steel frame Spindle and anvil made of hardened steel, carbide tipped Heat insulators Rapid drive with integrated ratchet Locking device setting standard (measuring range of 25-50 mm) instruction manual case Technical Data Order no. Measuring range mm Graduation value mm Error limit µm Spindle diameter […]

AUTHOR RATE
MAGNETIC DIAMOND DRESSER HOLDER

Small & compact size Powerful holding of the magnet on the machine table. Easy holding of the diamond dresser.   Sr. No. Art No. Size (MM) Magnetic Pull 1 2119.01 80 L X 50 W X 70 H 70 Kg

AUTHOR RATE
MILLIMESS 1003 MECHANICAL DIAL COMPARATOR

Large, high contrast dial face Adjustable tolerance markers Lockable fine adjustment screw Shockproof movement Mounting shank and measuring spindle are both made of hardened stainless steel Measuring spindle is mounted in a high precision ball guide for minimal hysteresis Resistant to lateral forces (side play) acting on the measuring spindle Maximum sensitivity and accuracy are […]

AUTHOR RATE
Mitutoyo-SERIES 1-Back Plunger Type Dial Indicator

Back plunger type dial gauges are suitable for mounting onto leveling machine tool tables or inspection jigs, and for use in situations where standard dial gauges are difficult to read. Model 1960T and 1961T, which uses Mitutoyo’s proprietary shock-proofing mechanism, has excellent durability and shock resistance. DIMENSIONS Order No. A B C E F G […]

AUTHOR RATE
ADJUSTABLE SPANNERS

ADJUSTABLE SPANNERS CHROME FINISH TAPARIA Adjustable Spanners are:- Forged with high grade steel, and heat treated to give long trouble free service. Left hand thumb screw movement as standard.Right hand thumb screw movement available om request. Precision marked scale indicate correct jaw opening. Available in bright polished Nicel Chrome finish and Black Phosphate finish.Also available […]

AUTHOR RATEUSERS RATE (0)
ONE REVOLUTION PRECISION DIAL INDICATOR CODE – 2885

Eliminate the possibility of reading errors due to miscounting Shockproof Jeweled bearing Free stroke: 4.5mm With limit pointers Optional accessory: backs (page 132), contact points (page 128~131), lifting lever(code 6289-150)   Code Range Graduation Accuracy Hysteresis Range/rev Dial reading Remark 2885-008* 0.08mm 0.001mm 3µm 1.5µm 1mm 40-0-40 lug back 2885-008F* 0.08mm 00.001mm 3µm 1.5µm 1mm […]

AUTHOR RATEUSERS RATE (0)
ROUND BODY DIAL TEST INDICATOR CODE – 2391

Jeweled bearing Carbide contact point Adjustable two measuring directions Anti magnetic body Supplied with two clamps: diameter Ø4mm and Ø8mm Optional accessory: styli (page 138)   Code Range Graduation Accuracy Hysteresis Dial reading 2391-08* 0.8mm 0.01mm 13µm 3μm 0-40-0 *Supplied with manufacturer calibration certificate Check the PDF

AUTHOR RATE
Digital Caliper Code 1103

Small two liner content about Digital caliper

AUTHOR RATEUSERS RATE (0)
ULTRASONIC THICKNESS GAGE THROUGH COATING CODE ISU-300D

Two measuring modes, Echo-Echo (E-E) and Transmit-Echo (T-E): E-E is applicable for non-metallic coating (such as paint, plastic resin, etc.) on metal substrate, can penetrate coating and measure the thickness of substrate T-E is to measure the thickness of material without coating, such as metal, plastic, glass nylon resin, ceramics, rubber, ice, etc. Low and […]

AUTHOR RATEUSERS RATE (0)
PLAIN ANGLE PLATE

Plain Angle Plate We manufacture a wide range of Plain Angle Plate, which are largely used in various industries for clamping and holding work in vertical position. These plain angle plates are also used as a vertical reference for inspection and tooling purposes such as shaping, planning, milling, grinding, drilling etc. All six working faces […]

AUTHOR RATE
BENCH .VICE DOUBLE RIB (HEAVY DUTY)

CODE NO. 840 (Plain Model) CODE NO. 840S (Swivel Model) Fitted With SG Iron Nut SIZE IN NUMBER 0 1 2 3 4 5 6 8 SIZE IN INCHES 21/2 3 31/2 4 41/2 5 6 8 Width of Jaws 65 80 90 100 115 125 150 200 Opening of Jaws 70 85 110 120 […]

AUTHOR RATE
MARAMETER 22P-20 PORTABLE THICKNESS GAGES

Indicator built into gage frame for maximum ruggedness Lift lever for one hand operation Continuous reading dials with revolution counter for absolute measurement of thin materials, plastic films and small parts 6.3 mm / .25“ diameter, flat steel contacts Technical data Order no. Product type Measuring range inches Graduation value inch Probe_path_inch Size of measuring […]

AUTHOR RATE
Mitutoyo-550 Series – with Nib Style Jaws-ABSOLUTE Digimatic Caliper

Offers a resolution of 0.01mm with corresponding accuracy. Incorporates an Absolute measurement system. No need to reset the origin after switching (Refer to page D-8 for a description of Absolute measurement.) Code 550-301-10, 550-331-10, 550-311-10 and 550-341-10: IP67 (These models are not a waterproof type. Therefore a rustproofing shall be applied after use.) Allows integration […]

AUTHOR RATE
MICROMAR 40 AB – MICROMETERFOR MEASURING GROOVES, SPLINE SHAFTS, RECESSES, ETC.

MICROMAR 40 AB MICROMETER Reduced measuring surfaces Ø 3 mm Operating and display units with satin chrome finish Hard lacquered steel frame Spindle and anvil made of hardened steel, carbide tipped Heat insulators Rapid drive with integrated ratchet Locking device instruction manual setting standard (measuring range of 25-50 mm) case Technical Data Order no. Measuring […]

AUTHOR RATE
Mitutoyo-SERIES 167-Setting Standards for Screw Thread Micrometers

Used for accurately setting screw thread micrometers at the start or end of the measuring range. Metric Order No. Length Accuracy Metric (unified) 8 = 60° 167-261 25mm ±4µm 167-262 50mm ±5µm 167-263 75mm ±6µm 167-264 100mm ±7µm 167-265 125mm ±8µm 167-266 150mm ±9µm 167-267 175mm ±10µm 167-268 200mm ±11µm 167-269 225mm ±12µm 167-270 250mm […]

AUTHOR RATEUSERS RATE (0)
PRECISION GRINDING VICE

Used for holding the jobs, spark erosion operation, right angle grinding & Light machining. Made from high quality alloy steel. Accuracy for Square ness, Flatness & Parallelism within ±0.005mm. Jaw pressure on work piece is forward & downward for repeatable positioning & maximum holding power. All sides can be used as reference. Hardness – 60 […]

AUTHOR RATE
BAKER Thread Gauge: Metric

Thread Gauge: Metric Acceptance criteria for components The GO gauge when screwed by hand without using excessive force, should enter and pass the whole length of the workpiece thread. The NOT GO gauge when screwed by hand without being forced, should not enter the component by more than three complete turns. Check the PDF

AUTHOR RATE
Mitutoyo-SERIES 406-Digimatic straight line micrometer outside micrometer

Non-rotating spindle. Equipped with Ratchet Stop for constant measuring force. Metric Order No. Range Resolution Accuracy* Flatness Parallelism 406-250-30 0 – 25mm     0.001mm   ±3µm     0.3µm   3µm 406-251-30 25 – 50mm 406-252-30 50 – 75mm 406-253-30 75 – 100mm ±4µm 4µm   * Excluding quantizing error Inch/Metric Order No. Range […]

AUTHOR RATEUSERS RATE (0)
PH HOLDERS FAT

TOOLS Check the PDF

AUTHOR RATE
Mitutoyo-SERIES 116 – Interchangeable Anvil Type-Universal Micrometer

Non-rotating spindle type which accepts seven forms of optional interchangeable anvil / spindle tip (flat, spline, spherical, point, knife-edge, disk, and blade) for a wide range of applications. Equipped with Ratchet Stop for constant measuring force. Optional anvils / spindle tips for screw thread measurement (matching V and cone) are also available. SPECIFICATIONS Metric Order No. Range […]

AUTHOR RATE
Mitutoyo-Optional Accessories for Dial Test Indicators-Styli, Stems and Holders

Styli (for Metric Models Only*) * Except for universal type dial test indicator (513-304G). Stylus length affects the scale factor of an indicator. The styli provided as standard give a scale factor of unity. ø0.5mm ball-point 190547 (L=14.7mm) 190549 (L=20.9mm) 190654 (L=22.3mm) 190656 (L=44.5mm) ø0.7mm ball-point 190548 (L=14.7mm) 190550 (L=20.9mm) 190653 (L=22.3mm) 190655 (L=44.5mm) ø1mm […]

AUTHOR RATE
HEAVY DUTY ø3.2mm

NOGA BURR 3 NG1003 Will do almost all of your deburring jobs. Includes: NG-1 handle, S10, S20 and S35 blades. NOGA BURR 5 NG1005 Same as NG1003 but with 2 extra blades. Suitable for coarse to extra fine deburring operations. Includes: NG-1 handle, S10, S20, S35, S101 and S202 blades.   NG-1 Handle NG1000 NogaGrip-1 […]

AUTHOR RATE
Mitutoyo-SERIES 527, 571 – Hook End Type-Depth Gage

The end of the main beam is hook-shaped to allow depth and thickness measurements of a projected portion or lip in a hole, in addition to standard depth measurement. Coolant proof models achieve IP67 protection level. Enables stable depth measurement with a resolution of 0.01mm. ABSOLUTE Digital Caliper (Refer to page D-8 for ABSOLUTE function.) Digital […]

AUTHOR RATE
Mitutoyo-Mitutoyo-SERIES 573, 536 — ABSOLUTE Digimatic and vernier type-Neck Caliper-Tube Thickness Caliper

The beam-mounted jaw is a round bar that facilitates measurements of tube wall thickness. Digital models are IP67 Absolute type. No need to reset the origin after switching on. (Refer to page D-8 for a description of Absolute measurement.) Allows integration into statistical process control and measurement systems for models with measurement data output connector. Refer to page A-3. […]

AUTHOR RATE
Ridburr Swivel Blades

RB10 Blade Works best on Steel, Aluminum and Plastic. For right hand user. Made of HSS M2     RB20 Blade Works best on Brass and Cast iron. For left and right hand user. Made of HSS M2     RB30 Blade Removes internal and external burrs. For right hand user. Made of HSS M2   RB100 Blade Super hand […]

AUTHOR RATEUSERS RATE (0)
WHEEL SPANNERS & SETS

BOX SPANNERS Up set forged from high grade manganese steel.Scientifically heat treated to give maximum strength, wear resistance and long life. Available with bright finish in Nickle Chrome and black phosphate finish for protection from corrosion. PRODUCT No. SIZES WT. GMS 1720/HD 1720 30 x 32 – HD1725 27 x 30 – 1728 24 x […]

AUTHOR RATE
SPECIALTY TOOLS

HANDLES Check the PDF   TOOLS Check the PDF

AUTHOR RATE
Digital Caliper Code 1117

Small two liner content about Digital Caliper

AUTHOR RATE
MARAMETER 852 TSZ INDICATING BENCH SNAP GAGE

Rugged steel frame can be inclined up to 45° from the sturdy base Measuring spindle and anvil are made of hardened stainless steel with mounting bore for insertion of interchangeable anvils Height adjustable stop Anvil spindle can easily be fine adjusted Constant measuring force as a result of built-in spring, eliminating user influence Technical data […]

Unoair Reversible Angle Drill & Air Traipping Wrench Dealer
AUTHOR RATEUSERS RATE (0)
REVERSIBLE ANGLE DRILL & AIR TRAIPPING WRENCH

D-31/D-41 Reversible Drills D-36 Reversible Angle Drills D-38/RY-311 Straight Drill D-4400 Air Tapping Drill SD 94-WS Air Tapping Wrench NS-50S Air Needle Scaler FC-510 Air Flux Chipper FC-502 Air Flux Chipper CH-104 Air Chipping/Riveting Hammer   Technical Specifications Model No Free Speed (rpm) Drilling Cap Overall Length (mm) Air Inlet Air Consumption  (cfm) Weight (kgs) […]

AUTHOR RATEUSERS RATE (0)
Baker Electronic Probe

Electronic Probe: 2900   Specifications 2900 Measuring travel ± 0.4 mm Total travel 1 mm Linearity ± 0.5% (of total measuring range) Repeatability 0.15 μm Measuring force 0.8 N Pre-travel Fixed Application Universal Environmental Protection (IEC 529) IP 64 Plunger guide Preloaded, caged linear ball bearing Cable 2 m., Polyurethane. Cable support spring N.A. Connecting […]

AUTHOR RATEUSERS RATE (0)
THREAD PITCH GAGE

PITCH GAGE CODE – 4820 Check the pitch of screw thread Accuracy: ±0.07mm Metric 60° screw Code Range Pitch of leaves included Quantity of leaves 4820-122 0.4 – 7.0mm 0.4, 0.5, 0.6, 0.7, 0.75, 0.8, 0.9, 1, 1.25, 1.5, 1.75, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7mm 22 4820-124 0.25 – 7.0mm […]

AUTHOR RATE
Mitutoyo SERIES 192 – Multi-function Type with SPC Data Output – Digimatic Height Gage

Double-column structure ensures high measuring accuracy. Ergonomic base fits comfortably in the hand. Bidirectional touch-trigger probe is available as an optional accessory. Character height of the LCD display has been increased (10mm to 11mm) and a high- contrast LCD display unit adopted, so that the readability is improved. Inclined handle improves slider ergonomics. Allows integration into statistical […]

AUTHOR RATE
Special Knurling tool Holder

Rapid offers special knurling tools & holders. As per customer request and in consultation with our technical team, Rapid manufactures tools which suites the specific need of customer application. Individual applications call for Special Customised tools.

AUTHOR RATE
MICROMAR 40 SA MICROMETER

Operating and display units with satin chrome finish Hard lacquered steel frame Spindle and anvil made of hardened steel, carbide tipped Heat insulators Rapid drive with integrated ratchet Locking device instruction manual setting values 125 mm / 175 mm case Technical Data Order no. Measuring range mm Graduation value mm Spindle diameter Spindle thread pitch_mm […]

AUTHOR RATEUSERS RATE (0)
RADIUS GAGE SET

RADIUS GAGE CODE – 4801   Code Range Radius of leaves included (mm) Quantity of leaves (internal + external ) Accuracy 4801-17 1 – 7mm 1, 1.25, 1.5, 1.75, 2, 2.25, 2.5, 2.75, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7 17+17 ±0.03mm 4801-16 7.5 – 15mm 7.5, 8, 8.5, 9, 9.5, 10, 10.5, […]

AUTHOR RATEUSERS RATE (0)
SHOT AND GRIT BLASTING SURFACE ROUGHNESS SPECIMEN CODE -ISR-CS017

To check the roughness of steel surfaces which have been blast cleaned before painting Meets ISO 8503/1 Rust-proof, made of pure Nickel   Code Machining method Roughness (Ra) Roughness (Rz) Quantity ISR-CS017 Shot blasting 3.2, 8, 13, 18µm 19.2, 48, 78, 108µm 4pcs ISR-CS018 Grit blasting 3.2, 10.5, 18, 25µm 19.2, 63, 108, 150µm 4pcs […]

Unoair Push start auto shut off noiseless screwdriver Dealer
AUTHOR RATE
PUSH START AUTO SHUT-OFF NOISELESS SCREW DRIVER

Pistol Handle Trigger Start Shut Off Air Screw Driver Cushion Clutch Air Screw Driver (Pistol Type) Straight Handle Push Start Shut Off Screw Driver Angle Type Lever Start Shut Off Screw Driver Cushion Clutch Air Screw Driver (Straight Type) Straight Handle Lever Start Shut Off Screw Driver STD – 15110 – AC Air Cylinder Series […]

AUTHOR RATEUSERS RATE (0)
Baker Microprocessor based Twin Channel: 2041 Analogue

Microprocessor based Twin Channel: 2041 Analogue Digitally driven, Analogue Galvanometer type measurement display Five metric and five inch measuring ranges FEATURES: State-of-the-art technology with host of features, a must for today’s shop process quality engineering Two level password, prevents unauthorized alteration Multiple-level display intensity for operators comfort Inch & metric measuring ranges Static & dynamic […]

AUTHOR RATE
Mitutoyo-SERIES 2 – Standard One Revolution Type for Error-free Reading, Waterproof Type-Dial Indicators

Mitutoyo’s unique shock-proof mechanism is incorporated, providing improved resistance to shock due to sudden spindle retraction caused by impact. This series has been developed to eliminate the possibility of reading errors due to miscounting multiple revolutions. The dead zone in red indicates “accuracy not guaranteed”. One revolution type Back plunger dial gages are also available. […]

AUTHOR RATE
MicroGauge Two Point Bore Gauge

The new MicroGauge 2-point bore gauging system has been designed specifically for the measurement of small bores between 1.0-10.0mm. Featuring a completely new digital readout and extremely compact overall dimensions, the MicroGauge is truly a pocket-sized instrument. Digital readout and measuring head together are about the same size and format as a ballpoint pen which […]

Unoair Micro Die Grinders Sanders Dealer
AUTHOR RATEUSERS RATE (0)
MICRO DIE GRINDERS SANDERS

DG-30 (M) Die Grinder DG-32 (M) Heavy Duty Die Grinder DG-33 (M)Ext. Die Grinder DG-34 (M) Ext.Die Grinder DG-36 (M) Angle Die Grinder DG-37 (M) Air Angle Sander S-39A Air Sander RY-135 Die Grinder RY-170L Angle Grinder MG-80 Die Grinder  MG-01 Die Grinder  DG-GS38N Die Grinder  DG-GS38L Die Grinder RY-316B Die Grinder Ry-160 Micro Die […]

AUTHOR RATE
Mitutoyo-SERIES 1 – Compact One Revolution Type for Error-free Reading-Dial Indicators

Mitutoyo’s unique shock-proof mechanism is incorporated, providing improved resistance to shock due to sudden spindle retraction caused by impact. This series has been developed to eliminate the possibility of reading errors due to miscounting multiple revolutions. The dead zone in red indicates “accuracy not guaranteed” . One revolution type Back plunger dial gages are also […]

Balaji Spherical Washer With Conical Seat Dealer
AUTHOR RATE
SPHERICAL WASHER WITH CONICAL SEAT

IS4297-1996 TYPE AID IN6319-1991 MATERIAL En8, heat treated 22 to 30 HRC Blackodized     MODEL No. Bolts For d1 d2 h1 d3 d4 h2  BESWCS 8  MB  8.4  17  3.2  9.6  14.5  3.5  BESWCS 10  M 10  10.5  21  4.0  12  18.5  4.2  BESWCS 12  M 12  13  24  4.6  14.2  20  5.0  BESWCS […]

AUTHOR RATE
MICROMAR 40 SM MICROMETER

Operating and display units with satin chrome finish Maximum stability Stainless spindle is hardened throughout and ground Disc-type anvils are hardened and lapped Chrome plated steel frame, heat insulated Rapid drive with integrated ratchet Locking device instruction manual case Technical Data Order no. Measuring range mm Graduation value mm Error limit µm Parallel error in […]

AUTHOR RATE
MARAMETER XLI-22P-20 PORTABLE THICKNESS GAGES

Indicator built into gage frame for maximum ruggedness Lift lever for one hand operation Continuous reading dials with revolution counter for absolute measurement of thin materials, plastic films and small parts 6.3 mm / .25“ diameter, flat steel contacts Technical data Order no. Product type Measuring range inches Measuring range mm Throat depth mm Probe_path_inch […]

AUTHOR RATE
Mitutoyo-SERIES 573, 536 — ABSOLUTE Digimatic and vernier type-Blade Type Caliper

The thin blade-type jaws fit into very small grooves and make previously difficult outside measurements far easier to obtain. The outside measuring faces are carbide tipped. Allows step measurement. Digital models are IP67 Absolute type. No need to reset the origin after switching on. (Refer to page D-8 for a description of Absolute measurement.) Allows integration […]

AUTHOR RATEUSERS RATE (0)
COATING THICKNESS GAGE CODE ISO-2000FN

Suitable for small surfaces, concave or convex surfaces after calibrated Magnetic induction probe (Fe) is to measure the thickness of non-magnetic coating on magnetic substrate Substrate: iron, steel, magnetic stainless steel (does not include non-magnetic stainless steel) Coating: zinc, copper, chrome-tin, plastic powder, paint (does not include nickel) Eddy current probe (NFe) is to measure the […]

AUTHOR RATEUSERS RATE (0)
DIGITAL CALIPER CODE – 1112

Resolutions: 0.01mm/0.0005* Buttons : zero, mm/inch, on/off, ABS, data preset Battery  SR44 or LR44 Data Output Meet DIN862 Optional accessory: data output system     Code Range Accuracy L a b c d 1112-150 0-150mm/0-6″ ±0.03mm 236 21 16 16 40 1112-200 0-200mm/0-8″ ±0.03mm 286 24 19 16 50 1112-300 0-300mm/0-12″ ±0.03mm 400 25 20.5 […]

Kristeel Steel Protractor Dealer
AUTHOR RATE
STEEL PROTRACTOR

MODEL 1502 STAINLESS STEEL DEGREE PROTECTOR (SQUARE-HEAD) For Machinists, Draughtsmen, layout men & other mechanics. Protractor has easy etched reading graduations from 0o to 180o on opposite directions. Elegant Design Accurate Graduation Polished Finish   MODEL 1501 – A PROTRACTOR CUM DEPTH GAUGE (D-HEAD) For Machinists, Draughtsmen, layout men & other mechanics. Protractor has easy […]

AUTHOR RATE
Mitutoyo-SERIES 2 – Standard One Revolution Type for Error-free Reading, Lightweight Type-Dial Indicators

Excellent water- and drip-proof characteristics (IP43). Smooth movement thanks to the improved design of bush and stem. Application of a hard coating on the surface of the crystal makes the gage scratch- and oil-resistant. Lightweight type (70g). DIMENSIONS * When installing an optional back (refer to page F-55 for details) please separately prepare 4 fixing […]

AUTHOR RATEUSERS RATE (0)
BLADE POINT

  Code Material of measuring face D W   6282-1801 steel 0.4 2   6282-1802 steel 0.6 2   6282-1803 steel 1 4 Check the PDF

AUTHOR RATEUSERS RATE (0)
BAKER UNIVERSAL GAUGE

The Bowers Universal Gauge’s ingenious modular format enables it to be quickly configured to suit almost any measuring challenge. Whether measuring internally or externally, the Universal’s clever constant pressure device ensures accuracy and consistency of reading. The gauge’s findings are displayed on its built in clear digital readout. The unique modular construction of the Bowers […]

AUTHOR RATE
Mitutoyo-SERIES 193-Digit Outside Micrometers

Mechanical digit counter with 0.01mm or .001” resolution for quick and error-free reading. Measuring faces: Carbide Equipped with Ratchet Stop for constant measuring force. SPECIFICATIONS Metric With ratchet stop Order No. Range Graduation Accuracy 193-101 0 – 25mm 0.01mm     ±2µm 193-111 0.001mm 193-102   25 – 50mm 0.01mm 193-112 0.001mm 193-103   50 – […]

AUTHOR RATEUSERS RATE (0)
INTERNAL MICROMETER WITH INTERCHANGEABLE ANVILS CODE – 3226

Graduation: 0.01mm Optional accessory: ball tips (code 7391) V-shaped and cone-shaped anvils(code 7321), zero block for V-shaped and cone-shaped anvils(code 3226-SP)     Check the PDF

AUTHOR RATE
MICROMAR 40 EWR – DIGITAL OUTSIDE MICROMETER, IP 65

MICROMAR 40 EWR DIGITAL MICROMETER High contrast analog display Stainless spindle is hardened throughout and ground Spindle and anvil are carbide tipped Rapid drive Ratchet is integrated in the thimble Lacquered steel frame, heat insulated Digimatic Opto RS232C USB Battery life approx. 2 years IP 65 instruction manual battery setting standard (measuring range of 25-50 […]

AUTHOR RATE
3-WAY TILTING & SWIVLING VICE

CODE NO. 830   SIZE IN INCHES 4 6 Width of jaws in mm 100 150 Opening of jaws in mm 100 150 Opening of jaws in mm 38 52 Depth of jaws i mm 450 530 Length overall in mm 195 285 Height overall 830 in mm 30 62 Check the PDF

AUTHOR RATEUSERS RATE (0)
BAKER LEVER DIALS

MODEL 29/38 LEVER DIAL GAUGES FEATURES: Specification: IS, DIN, ANSI & JIS Every gauge carries a calibration certificate giving actual values Auto reversal mechanism Fitted with jewels and Swiss miniature ball bearings for smoother operation Robust and highly sensitive gauge suitable for workshop use Metric Gauges conform to IS 11498 and for the European market to […]


Most Viewed Products

These products are top rated by our users

We in Gokul Traders have the vision to maintain the standard set by Laddha Group since ages of Quality, Trust, Precision and walk with the changing times and tides still maintaining what has been our strength, Customer Relations. Our hearts are filled with a burning desire and passion to provide top most precision, quality and most importantly, in time. We do not just sell, we even are passionate about making people, industries and students aware about different tools and equipment which can make their life easy. We are part of the Prestigious Laddha Group, which for so many years with our Dedication and our Ethics have been showered with Customer Goodwill. We follow the commitment, we talk the talk and walk the walk.

 

Our Esteemed Clients

      




Gokul Traders Copyright © 2010-18 Developed by Shades Of Web. All rights reserved.