• Dedicated to inside measurement with minimum-value Hold and tolerance judgement functions.
• Measurement data memory function (9 measurement results can be stored)
• Simple operation of many functions with five buttons and status icons.
• Wide LCD and new analog bar graph are now standard on all models.
• Sampling is performed fifty times per second for accurate detection of maximum and minimum values.

SPECIFICATIONS
Metric

Order No.*	Range	Resolution	Accuracy*1	Hysteresis*1	Repeatability*1	Power supply	Battery life (normal use)*2	Net weight
543-310B	12.7mm	0.001/0.01mm	0.003mm	0.002 mm	0.002 mm	CR2032 x 1 pc.	Approx. 1 year	170 g

*Flat back only

Inch/Metric

Order No.*	Range	Resolution	Accuracy*1	Hysteresis*1	Repeatability*1	Power supply	Battery life (normal use)*2	Net weight
543-311B	.5″/12.7mm	.00005/.0001/.0005″/ 0.001/0.01 mm	±.00010″ / 0.003 mm	.00010″ / 0.002 mm	.00010″ / 0.002 mm	CR2032 x 1 pc.	Approx. 1 year	170 g
543-312B

*Flat back only

*1 Does not include quantizing error (±1 count). Valid for resolution set to 0.001mm/.00005″
*2 Applies only if not connected to a data processor. Battery life depends on use of the indicator. Use the above value as a guide only. (TIP) Battery life with Peak detection mode and FAST mode ON is about 4.5 months.
Notes:
1) Min. hold: sample rate is 50 readings/sec; maximum trackable rate of change is 50μm/sec.
2) All instruments in this series are of the flat back type.
3) All instruments in this series can be only used for inside diameter measurement.

DIMENSIONS

Note 1: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.
Note 2: Inch (ANSI/AGD Type) dial indicators are provided with a stem of 3/8″ dia. and #4-48UNF thread mount for the contact point.

Functions
Minimum value detection function
Preset function (3 Preset values can be stored)
Tolerance judgement function (3 sets of upper and lower
limits can be stored)
Resolution selection function
Analog bar resolution selection function
Key lock function
in/mm conversion (when external device is connected)
Display hold function (when external device is connected)
Data saving/calling function (when external device is connected)
Data output function
External PC setting input function
Display rotation function
Low battery/voltage alarm display
Error alarm display

Optional Accessories
• SPC Cable:
No.905338 (1m)
No.905409 (2m)
• USB Input Tool Direct (2m) : No.06ADV380F
• Connecting Cables for U-WAVE-T (160mm) :
No.02AZD790F
For footswitch : No.02AZE140F
Refer to page F-60 for details.
• Digimatic Mini-Processor DP-1VR: 264-504
• Parameter setup kit : No.21EZA313
Note: Parameter setting software (can be downloaded freely from Mitutoyo website) is also required.

The ABSOLUTE Digimatic Bore Gage

ABSOLUTE Digimatic Bore Gages, which integrate the display with a bore gage measuring unit, are also available.
Refer to pages C-41 and C-42 for details.

• Run-out/MAX/MIN Hold function enables GO/±NG judgement for peak or difference values.
• Simple operation of many functions with five buttons and status icons.
• Wide LCD and new analog bar graph are now standard on all models.
• Sampling is performed fifty times per second for accurate detection of maximum and minimum values.

SPECIFICATIONS
Metric

Order No.(w/lug, flat-back)	Range	Resolution	Accuracy*1	Hysteresis*1	Repeatability*1	Power supply	Battery life (normal use)*2	Net weight
543-300	12.7mm	0.001/0.01mm	0.003mm	0.002mm	0.002mm	CR2032 x 1 pc.	Approx. 1 year	180 g
543-300B								170 g

Inch/Metric

Order No.(w/lug, flat-back)	Range	Resolution	Accuracy*1	Hysteresis*1	Repeatability*1	Power supply	Battery life (normal use)*2	Net weight
543-301	.5″/12.7mm	.00005/.0001/.0005″/ 0.001/0.01mm	±.00010″ / 0.003mm	.00010″ / 0.002mm	.00010″ / 0.002mm	CR2032 x 1 pc.	Approx. 1 year	180 g
543-301B								170 g
543-302								195 g
543-302B								170 g

Notes:
1) GO/±NG judgment result is visual and cannot be output.
2) Max./Min. hold: Sample rate is 50 readings per sec. Maximum trackable rate of change is 50μm per sec.
3) Order numbers suffixed “B” have a plain back.
*1 Does not include quantizing error (±1 count). Valid for resolution set to 0.001mm/.00005″ and coefficient A=1.
*2 Applies only if not connected to a data processor. Battery life depends on use of the indicator. Use the above value as a guide only. (TIP) Battery life with Peak detection mode and FAST mode ON is about 4.5 months.

DIMENSIONS

Note 1: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.
Note 2: Inch (ANSI/AGD Type) dial indicators are provided with a stem of 3/8″ dia. and #4-48UNF thread mount for the contact point.

Functions
Peak value hold function (maximum and minimum value)
Runout value Hold function
(difference between maximum/minimum values)
Zeroset function (INC system)
Preset function (ABS system)
Counting direction switching function
Tolerance judgement function (P1, P2, P3, and INC can be stored)
Resolution selection function
Simple calculation function f(x)=Ax
Analog bar resolution selection function
Key lock function
in/mm conversion (inch/mm models)
Display hold function (when external device is connected)
Data output function
External PC setting input function
Display rotation function (330°)
Low battery/voltage alarm display
Error alarm display
Optional Accessories
• Lifting
Lifting lever
No.21EZA198 (ISO/JIS/DIN Type),
No.21EZA199 (ASME/ANSI/ AGD Type)
Lifting knob
No.21EZA105 (ISO/JIS/DIN Type),
No.21EZA150 (ASME/ANSI/ AGD Type)
Lifting cable No. 540774
• SPC Cable:
No.905338 (1m)
No.905409 (2m)
• USB Input Tool Direct (2m) : No.06ADV380F
• Connecting Cables for U-WAVE-T (160mm):
No.02AZD790F
For footswitch: No.02AZE140F
Refer to page F-60 for details.
• Digimatic Mini-Processor DP-1VR: 264-504
• Parameter setup kit: 21EZA313
Note: Parameter setting software (can be downloaded freely from Mitutoyo website) is also required.

• Contact points for Mitutoyo’s dial indicators (Refer to pages F-51 to F-54 for details.)
• Interchangeable backs for 2 series (Refer to page F-55 for details.)
• Measuring stands. (Refer to page F-79 to F-85 for details.)

• Our unique ABS sensor restores the last origin position automatically when the indicator is
  turned on.
• The chance of overspeed errors has been eliminated thanks to the ABS sensor.
• Rated to IP66: can be used satisfactorily even in adverse environments where the indicator is subject to splashing by cutting fluid or coolant.
• Slim body design (body width: only 35mm) is advantageous in multipoint measurement situations where space is restricted. The LCD readout can also be rotated 180° to allow reading from the most convenient direction.
• Succeeded in digitalization of the Back Plunger type widely used for dial indicators for ID-B.  A 5mm-stroke plunger with a higher degree of accuracy has been implemented by adopting a direct reading scale for plunger displacement.
• Built-in tolerance judgment function provides OK, +NG, or –NG judgment of measurement with respect to the preset upper and lower limit values, indicating the status of a measurement with the appropriate symbol. The symbols can be displayed much larger.
• Equipped with a data output port that enables incorporation into measurement networking and statistical process control systems.
• There is a choice of convenient Interface Input Tools which enable the conversion of measurement data to keyboard signals and directly input them to cells in off-the-shelf spreadsheet software such as Excel.

SPECIFICATIONS
Metric

Order No.	Range	Resolution	Accuracy*	Remarks
543-570	12.7mm	0.01mm	0.02mm	Slim type ID-N
543-580	5.0mm			Back plunger type ID-B
543-575	12.7mm	0.01mm / 0.001mm	0.01mm / 0.003mm	Slim type ID-N
543-585	5.0mm			Back plunger type ID-B

Inch/Metric

Order No.	Range	Resolution	Accuracy*	Remarks
543-571	.5”	.0005”, 0.01mm	.001”	Slim type ID-N
543-581	.2”			Back plunger type ID-B
543-576	.5”	0.01mm / 0.001mm .0005” / .00005”	.00012”	Slim type ID-N
543-586	.2”			Back plunger type ID-B

*Quantizing error of ±1 count is excluded

Usage examples

DIMENSIONS

Note 1: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.
Note 2: Inch (ANSI/AGD Type) dial indicators are provided with a stem of 3/8″ dia. and #4-48UNF thread mount for the contact point.

Technical Data
Display: 6-digit LCD and sign
Scale type: ABSOLUTE electrostatic linear encoder
Max. response speed: Unlimited (Measurement by scanning
cannot be performed)
Measuring force: 2.5N or less (ID-N)
2.0N or less (ID-B)
Stem dia: 8mm (ISO/JIS type) or 3/8″ (ANSI/AGD type)
Standard contact point: 901312 (ISO/JIS type)
21BZB005 (ANSI/AGD type)
Battery SR44 (1pc.) : 938882 for initial
operational checks (standard accessory)
Battery life: Approx. 7,000 hours of continuous use Functions
Zero-setting, Presetting, Direction switching, Tolerance
judgment, Display hold, Data output,
inch/mm conversion (inch/mm models), LCD readout reversal
Alarm: Low voltage, Counting value composition error,
Overflow error, Tolerance limit setting error
Optional accessories
• Lifting knob (only for ID-N)
No.21EZA105 (ISO/JIS type)*
No.21EZA150 (ASME/ANSI/AGD type)*
Spindle can be manually lifted. Remove the spindle cap for
ID-N and attach the lifting knob to the spindle. Note that
water resistance is not maintained in this configuration.

Using the lifting knob

• Lug
No.21EZA145 (ISO/JIS type)
No.21EZA146 (ASME/ANSI/AGD type)
• Arm for ID-B (mode-to-order)
• Rubber boot
For oil resistance (NBR) No.02ACA376 (for ID-N)
No.125317 (for ID-B)
For durability (silicon) No.238774 (for ID-N)
No.21EAA212 (for ID-B)
• SPC cable:
No.21EAA194 (1m)
No.21EAA190 (2m)
• USB Input Tool Direct (2m): No.06ADV380G
• Connecting Cables for U-WAVE-T (160mm)  : No.02AZD790G
For footswitch: No.02AZE140G
Refer to page F-60 for details.
• Bifurcated connecting cable with zero-setting terminal:
No.21EAA210 (1m)
No.21EAA211 (2m)
Two of the wires inside the cable are separated for zero setting without touching the SET switch on the main body.
Use these cables in combination with commercially available switches. Zero setting is performed by briefly connecting these two wires together (less than a second), and ABS preset & recall by connecting for a second or more.
• Contact points for Mitutoyo’s dial indicators (Refer to pages F-51 to F-54 for details.)

Bifurcated connecting cable with zero-setting terminal

• The ABS (absolute) sensor restores the last origin position automatically when the indicator is turned on.
  Note: Regarding origin setting, refer to “Origin Setting of Digimatic Indicators” on page F-18.
• Thanks to Mitutoyo’s ABSOLUTE Linear Encoder, reliability has been increased due to elimination of over-speed errors.
• Tolerance-judging measurement is available by setting upper and lower limit values.
• Battery life of approx. 7,000 hours in continuous use has been achieved with only one battery.
• Equipped with a data output port that enables incorporation into measurement networking and statistical process control systems.

Large LCD
The large LCD incorporates 11mm characters giving 1.5 times the character area of conventional products (which
display 8.5mm characters) making measurement values much easier to read.

Three large buttons
The popular three-large button design, which is used in products such as the ABS coolant proof Digimatic indicators ID-N/B, makes buttons easier to press and operations easier to perform.

330º rotary display
The display can be rotated 330°, allowing use at a position where you can easily  read the measurement  value.

Calculation: f (x) = Ax
Mounting the ID-CX on a measuring jig and setting the multiplying factor (to any practical value) allows direct indicationof size (see example below) without using a conversion table  and so improves measurement efficiency.

Function locking
Ensures reliability of measurement by locking the settings to prevent preset function settings from being changed by mistake.

SPECIFICATIONS

Metric

Order No. (w/ lug, flat-back)		Range	Resolution	Overall accuracy*	Measuring force	Remarks
543-390	543-390B	12.7mm	0.001mm	0.003mm	1.5N or less	—
543-394	543-394B				0.4N – 0.7N	Low measuring force
—	543-470B	25.4mm			1.8N or less	—
—	543-490B	50.8mm		0.005mm	2.3N or less	—
543-400	543-400B	12.7mm	0.01mm	0.02mm	0.9N or less	—
543-404	543-404B				0.2N – 0.5N	Low measuring force
—	543-474B	25.4mm			1.8N or less	—
—	543-494B	50.8mm		0.04mm	2.3N or less	—

* Hysteresis: 0.001mm/0.01mm Resolution Type: 0.002mm
0.01mm Resolution Type: 0.02mm
* Repeatability: 0.001mm/0.01mm Resolution Type: 0.002mm
0.01mm Resolution Type: 0.02mm

Inch/Metric

Order No. (w/ lug, flat-back)		Range	Resolution	Overall accuracy*	Measuring force	Remarks
543-391	543-391B	.5”	.0005″/ .0001″/ .00005″/ .001mm / 0.01mm	.0001”	1.5N or less	—
543-392	543-392B				1.5N or less	—
543-395	543-395B				0.4N – 0.7N	Low measuring force
543-396	543-396B				0.4N – 0.7N	Low measuring force
—	543-471B	1”			1.8N or less**	—
—	543-472B				1.8N or less**	—
—	543-491B	2”		.0002”	2.3N or less**	—
—	543-492B				2.3N or less**	—
543-401	543-401B	.5”	.0005”/0.01mm	.001”	0.9N or less	—
543-402	543-402B				0.9N or less	—
543-405	543-405B				0.2N – 0.5N	Low measuring force
543-406	543-406B				0.2N – 0.5N	Low measuring force
—	543-475B	1”			1.8N or less**	—
—	543-476B				1.8N or less**	—
—	543-495B	2”		.0015”	2.3N or less**	—
—	543-496B				2.3N or less**	—

* Hysteresis: .0005”/.0001”/.0005”/0.001mm/0.01mm
Resolution Type: .00010”/0.002mm
.0005”/0.01mm Resolution Type: .0010”/0.02mm
* Quantizing error of ±1 count is excluded
** Applies for a spindle orientation between the spindles
* Repeatability: .0005”/.0001”/.0005”/0.001mm/0.01mm
Resolution Type: .00010”/0.002mm
.0005”/0.01mm Resolution Type: .0005”/0.02mm

DIMENSIONS

Note 1: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.
Note 2: Inch (ANSI/AGD Type) dial indicators are provided with a stem of 3/8″ dia. and #4-48UNF thread mount for the contact point.
Note 3: Products with an Order No. suffixed “B” have a plain back, and other models have a center lug back.
Refer to page F-55 for details of the backs.

Technical Data
Accuracy: Refer to the list of specifications (excluding quantizing error)
Resolution: 
0.01mm type 0.01mm
0.001mm type 0.01mm/0.001mm
.0005″/0.01mm type .0005″/0.01mm
.00005” /0.001mm type .0005 ”/.0001”/.00005 ” / 0.01mm/0.001mm
Display: 6-digit LCD and sign
Scale type: ABSOLUTE electrostatic linear encoder
Max. response speed: Unlimited (Measurement by scanning cannot be performed)
Measuring force: Refer to the list of specifications
Stem dia.: 8mm (ISO/JIS type) or 3/8”(ANSI/AGD type)
Battery: SR44 (1 pc.), 938882 for initial
operational checks (standard accessory)
Battery life: Approx. 7,000 hours of continuous use
Dust/Water protection level: IP42
Functions
Preset, Zeroset, GO/±NG judgment, Counting
direction switching, Power ON/OFF, Simplified calculation,
Function lock, Data hold, Data output,
inch/mm conversion (inch/mm models)
Alarm: Low voltage, Counting value composition error,
Overflow error, Tolerance limit setting error

Optional Accessories

•Lifting
Lifting lever:
No.21EZA198 (12.7mm/.5” ISO/JIS type)
No.21EZA199 (12.7mm/.5” ASME/ANSI/AGD type)
Lifting knob:
No.21EZA105 (12.7mm/.5” ISO/JIS type)*
No.21EZA150 (12.7mm/.5” ASME/ANSI/AGD type)*
No.21EZA197 (25.4mm/1” models)
No.21EZA200 (50.8mm/2” models)
Lifting cable: No.540774
Lifting lever: No.137693
(for measuring range: 25.4 and 50.8mm)
(supplied with 25.4mm and 50.8mm models as standard.)
• Auxiliary spindle spring:
No.02ACA571 (25.4mm/1” models)**
No.02ACA773 (50.8mm/2” models)**
• Lug-on-senter back:
No.101040 (25.4mm/1” and 50.8mm/2”, ISO/JIS type)
No.101306
(25.4mm/1” and 50.8mm/2”, ASME/ANSI/AGD type)
* Not available for low measuring force models.
**Required when orienting the indicator upside down.
• SPC Cable:
No.905338 (1m)
No.905409 (2m)
• USB Input Tool Direct (2m): 06ADV380F
• Connecting Cables for U-WAVE-T (160mm):
No.02AZD790F
For footswitch (02AZE140F)
Refer to page F-60 for details.
• Digimatic Mini-Processor DP-1VR: 264-504
• Contact points for Mitutoyo’s dial indicators (Refer to pages F-46 to F-49 for details.)
Interchangeable backs for 2 series (Refer to page F-50 for details.)
• Measuring stands (Refer to page F-80 for details.)

Setting measuring force on low measuring force models
• 543-404/404B/405/405B/406/406B

Spindle orientation	Spring	Weight(approximately 0.1N)	Maximum measuring force
Pointing vertically downward	Yes	Yes	0.5N or less
	Yes	No	0.4N or less
	No	Yes	0.3N or less
	No	No	0.2N or less
Horizontal	Yes	No	0.3N or less

Note) Operation using configurations other than shown above is  not guaranteed.

• 543-394/394B/395/395B/396/396B

Spindle orientation	Spring	Weight(approximately 0.1N)	Maximum measuring force
Pointing vertically downward	Yes	Yes	0.7N or less
	Yes	No	0.6N or less
	No	Yes	0.4N or less
	No	No	Not guaranteed
Horizontal	Not guaranteed

Note) Operation using configurations other than shown above is
not guaranteed.

• Solar powered An environmentally friendly measuring instrument that does not require batteries, eliminating the hassle and cost of battery replacement. Can operate under minimum light conditions of 40 lux—lower than the level in a warehouse.
• Built-in recharger The large-capacity built-in reservoir capacitor allows you to use the indicator for long periods of time under light conditions below the minimum level.*
• User-friendly buttons All functions can be accessed by using the two or three large buttons on the front of the indicator.
• Origin recorded even if display disappears. The indicator includes an ABS (absolute) sensor that allows the previously set origin to be restored even if the display disappears due to insufficient light, making it easy to resume measurement.  This feature makes ID-SS ideal for long-time or multi-point measurement.

SPECIFICATIONS
Metric

Order No.	Range	Resolution	Accuracy			Remarks
			Overall*	Hysteresis*	Repeatability*
543-500	12.7mm	0.001mm	0.003mm	0.002mm	0.002mm	With lug
543-500B						Flat
543-505		0.01mm	0.02mm	0.02mm	0.01mm	With lug
543-505B						Flat

Inch/Metric

Order No.	Range	Resolution	Accuracy			Remarks
			Overall*	Hysteresis*	Repeatability*
543-501	.5”	.00005”/0.001mm	±.0001”/0.003mm	.0001”/0.002mm	.0001”/0.002mm	With lug
543-501B						Flat
543-502						With lug
543-502B						Flat
543-506		.0005/0.01mm	±.0010”/0.02mm	.0010”/0.02mm	.005”/0.01mm	With lug
543-506B						Flat
543-507						With lug
543-507B						Flat

* Quantizing error of ±1 count is excluded.

Dimensions

Note 1: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.
Note 2: Inch (ANSI/AGD Type) dial indicators are provided with a stem of 3/8″ dia. and #4-48UNF thread mount for the contact point.

Technical Data

Display: 6-digit LCD and sign
Scale type: ABSOLUTE electrostatic linear encoder
Measuring force: 1.5 N or less
Usable positions: All
Power supply: Solar battery (for indoor use)
Minimum Operating light: 40 lux
Note: A built-in reservoir capacitor allows a fully charged
ID-SS to be used for about 3.5 hours under light conditions below the minimum level.
The charging time differs depending on the environment, but it usually takes about 1.5 hours for a fully discharged
ID-SS to fully recharge under light conditions of 500 lux.
Maximum response speed: No limit (scan-type measurement is not supported)
Stem dia: 8mm (ISO/JIS type) or 3/8″(ANSI/AGD type)

Functions
Origin set (zero-set)
Count direction switching
inch/mm conversion (inch/mm models)
Data output
Alarm: Counting value composition error
Insufficient illumination intensity or change

Optional Accessories

Optional Accessories

• Lifting

Lifting lever  No.21EZA198 (ISO/JIS/DIN Type),

No.21EZA199 (ASME/ANSI/ AGD Type)

Lifting knob No.21EZA105 (ISO/JIS/DIN Type),

No.21EZA150 (ASME/ANSI/ AGD Type)

Lifting cable (No. 540774)

• SPC Cable:

No.905338  (1m)

No.905409  (2m)

• USB Input Tool Direct (2m) : 06ADV380F
• Connecting Cables for U-WAVE-T (160mm):

No.02AZD790F

For footswitch 02AZE140F

Refer to page F-60 for details.

• Digimatic Mini-Processor DP-1VR: 264-504
• Contact points for Mitutoyo’s dial indicators

(Refer to pages F-51 to F-54 for details.)

Interchangeable backs for 2 series

(Refer to page F-55 for details.)

• Measuring stands (Refer to page F-79 to F-85 for details.)
• ID-SS can be used in standard work environments.

The following is excerpted from JIS Z9110:2010 General rules of recommended lighting levels; 5.4 Factories:

Luminance (lux)	Location (permissible work)
1500	Very detailed visual work
750	Detailed visual work; design and drawing work
500	Regular visual work such as work carried out in a factory; monitoring work such as using instrument panels and control panels
300	Administrative work carried out in a warehouse
200	Control rooms, bathrooms, and places where manual light work is carried out
150	Work such as loading, unloading, and shifting loads
100	Hallways, corridors, entrances and exits, and warehouses
50	Indoor emergency staircases

MARCATOR 1087 BRI DIGITAL INDICATOR

• Integrated wireless transmitter
• High-contrast LCD display
• Operating and display unit (bezel) can be rotated through 280°
• Lifter protection cap on the measuring spindle
• Clamping shaft and measuring pin made of hardened stainless steel
• Immediate measurements due to the Reference System

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Graduation value mm	Graduation value inch	Range of analog display mm	Range of analog display inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337664	1087 BRi	12.5 mm	.5″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 0.9	IP 42	8.5 mm

Functions

• ON/OFF
• RESET (set display to zero)
• mm/inch
• PRESET (enter anumerical value) from range 500 mm
• Reversal of counting direction
• TOL (enter tolerance limit values)
• START/STOP search for reversal point
• MAX/MIN memory for searching the reversal point
• ABS (display can be set to zero without losing reference to preset)
• 0 (set the analog display to zero)
• DATA (data transmission via connection cable)
• Factor (adjustable)
• LOCK (individual button lock)

• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Immediate measurements due to the Reference System
• Mounting shank and measuring spindle are both made of hardened stainless steel
• Protection cap on the end of measuring spindle

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Graduation value mm	Graduation value inch	Range of analog display mm	Range of analog display inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337662	1087 BR	12.5 mm	.5″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 0.9	IP 42	8.5 mm

Functions

• ON/OFF
• RESET (set display to zero)
• mm/inch
• PRESET (for entering a numerical value)
• Reversal of counting direction
• TOL (enter tolerance limit values)
• START/STOP search for reversal point
• MAX/MIN memory for searching the reversal point
• ABS (display can be set to zero without losing reference to preset)
• 0 (set the analog display to zero)
• DATA (data transmission via connection cable)
• Factor (adjustable)

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Graduation value mm	Graduation value inch	Range of analog display mm	Range of analog display inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337663	1087 Ri	12.5 mm	.5″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 0.85	IP 42	8.5 mm
4337665	1087 Ri	25 mm	1″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 0.9	IP 42	8.5 mm
4337667	1087 Ri	50 mm	2″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.007 mm	0.001 mm	Factory standard	1.25 – 2.7	IP 42	8.5 mm

Functions

• 0 (set the analog display to zero)
• ABS (display can be set to zero without losing reference to preset)
• AUTO-ON / OFF
• DATA (data transmission via connection cable)
• Factor (adjustable)
• LOCK (individual button lock)
• MAX/MIN memory for searching the reversal point
• ON/OFF
• PRESET (for entering a numerical value)
• RANGE (switch the measuring range and resolution)
• RESET (set display to zero)
• TIR (MAX-MIN) for testing flatness and concentricity
• TOL (enter tolerance limit values)
• Reversal of counting direction
• mm/inch

• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Immediate measurements due to the Reference System
• Lifter protection cap on the measuring spindle
• Mounting shank and measuring spindle are both made of hardened stainless steel

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Graduation value mm	Graduation value inch	Range of analog display mm	Range of analog display inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337660	1087 R	12.5 mm	.5″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 0.9	IP 42	8.5 mm
4337661	1087 R	25 mm	1″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 1.15	IP 42	8.5 mm
4337666	1087 R	50 mm	2″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.007 mm	0.001 mm	Factory standard	1.25 – 2.7	IP 42	8.5 mm
4337670	1087 ZR	12.5 mm	.5″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 0.9	IP 42	8.5 mm
4337671	1087 ZR	25 mm	1″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0,001 / 0,002 / 0,005 / 0,01 / 0,02 / 0,05	.00005″ / .0001” / .0002” / .0005″ / .001″ / .002″	± 0,01 / ± 0,02 / ± 0,04 / ± 0,1 / ± 0,2	± .0004″ / ± .001” / ± .002″ / ± .004″ / ± .01”	0.004 mm	0.001 mm	Factory standard	0.65 – 1.15	IP 42	8.5 mm

Functions

• ON/OFF
• RESET (set display to zero)
• mm/inch
• Reversal of counting direction
• PRESET (for entering a numerical value)
• TOL (enter tolerance limit values)
• MAX/MIN memory for searching the reversal point
• TIR (MAX-MIN) for testing flatness and concentricity
• ABS (display can be set to zero without losing reference to preset)
• DATA (data transmission via connection cable)
• Factor (adjustable)
• LOCK (individual button lock)

MARCATOR 1086 RI DIGITAL INDICATOR

• Integrated wireless transmitter
• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Mounting shank and measuring spindle are both made of hardened stainless steel
• Immediate measurements due to the Reference System

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337624	1086 Ri	12.5 mm	.5″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0.004 mm	0.001 mm	Factory standard	0.65 – 0.9	IP 42	11 mm
4337625	1086 Ri	25 mm	1″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0.004 mm	0.001 mm	Factory standard	0.65 – 1.15	IP 42	11 mm
4337626	1086 Ri	50 mm	2″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0.007 mm	0.001 mm	Factory standard	1.25 – 2.7	IP 42	11 mm
4337627	1086 Ri	100 mm	4″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0.008 mm	0.001 mm	Factory standard	1.8 – 3.5	IP 42	11 mm
4337628	1086 Ri	25 mm	1″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0.004 mm	0.001 mm	Factory standard	0 – 0	IP 42	11 mm

Functions

• ON/OFF
• RESET (set display to zero)
• mm/inch
• Reversal of counting direction
• PRESET (for entering a numerical value)
• TOL (enter tolerance limit values)
• <0> (tolerance GO / NO GO display mode)
• ABS (display can be set to zero without losing reference to preset)
• DATA (data transmission via connection cable)
• Factor (adjustable)
• LOCK (individual button lock)

MARCATOR 1086 RI DIGITAL INDICATOR

• Integrated wireless transmitter
• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Mounting shank and measuring spindle are both made of hardened stainless steel
• Immediate measurements due to the Reference System

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337134	1086 Ri	12.5 mm	.5″	0.01 mm	.0005″	0.02 mm	0.01 mm	Factory standard	0.65 – 0.9	IP 42	11 mm
4337135	1086 Ri	25 mm	1″	0.01 mm	.0005″	0.02 mm	0.01 mm	Factory standard	0.65 – 1.15	IP 42	11 mm
4337136	1086 Ri	50 mm	2″	0.01 mm	.0005″	0.02 mm	0.01 mm	Factory standard	1.25 – 2.7	IP 42	11 mm
4337137	1086 Ri	100 mm	4″	0.01 mm	.0005″	0.02 mm	0.01 mm	Factory standard	1.6 – 3.5	IP 42	11 mm

Functions

• ON/OFF
• RESET (set display to zero)
• mm/inch
• Reversal of counting direction
• PRESET (for entering a numerical value)
• TOL (enter tolerance limit values)
• <0> (tolerance GO / NO GO display mode)
• ABS (display can be set to zero without losing reference to preset)
• DATA (data transmission via connection cable)
• Factor (adjustable)
• LOCK (individual button lock)

MARCATOR 1086 WRI DIGITAL INDICATOR

• Integrated wireless transmitter
• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Mounting shank and measuring spindle are both made of hardened stainless steel
• Immediate measurements due to the Reference System

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337142	1086 WRi	12.5 mm	.5″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0.004 mm	0.001 mm	Factory standard	0.65 – 1.4	IP 54	11 mm
4337143	1086 WRi	25 mm	1″	0.001 mm / 0.001 mm / 0.002 mm / 0.005 mm / 0.01 mm	.00002″ / .00005″ / .0001″ / .0002″ / .0005″	0.004 mm	0.001 mm	Factory standard	1 – 2.25	IP 54	11 mm

Functions

• ON/OFF
• RESET (set display to zero)
• mm/inch
• Reversal of counting direction
• PRESET (for entering a numerical value)
• TOL (enter tolerance limit values)
• <0> (tolerance GO / NO GO display mode)
• ABS (display can be set to zero without losing reference to preset)
• DATA (data transmission via connection cable)
• Factor (adjustable)
• LOCK (individual button lock)

MARCATOR 1086 WRI DIGITAL INDICATOR

• Integrated wireless transmitter
• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Mounting shank and measuring spindle are both made of hardened stainless steel
• Immediate measurements due to the Reference System

Technical data

Order no.	Product type	Measuring span in mm	Measuring span (inches)	Resolution	Resolution inches	Error limit (mm)	Repeatability mm	Standard	Measuring force (N)	IP protection category	Height of digits
4337147	1086 WRi	12.5 mm	.5″	0.01 mm	.0005″	0.02 mm	0.02 mm	Factory standard	0.65 – 1.4	IP 54	11 mm
4337148	1086 WRi	25 mm	1″	0.01 mm	.0005″	0.02 mm	0.02 mm	Factory standard	1 – 2.25	IP 54	11 mm

Functions

• ON/OFF
• RESET (set display to zero)
• mm/inch
• Reversal of counting direction
• PRESET (for entering a numerical value)
• TOL (enter tolerance limit values)
• <0> (tolerance GO / NO GO display mode)
• ABS (display can be set to zero without losing reference to preset)
• DATA (data transmission via connection cable)
• Factor (adjustable)
• LOCK (individual button lock)