Vernier Calipers Archives - Page 4 of 11

Top-of-the-line digital caliper. Solar type caliper with no battery and IP67 protection assures waterproof reliability.

With no annoying origin restoration necessary, a measurement can be started any time and there is no restriction on operating speed.
The impact resistance of the display unit has been increased for improved usability in workshop conditions.
Waterproof function makes this Super Caliper suitable for use in an environment containing large amounts of cutting fluid or coolant. Operability is equivalent to the mechanical type caliper.
This SuperCaliper uses components that do not contain harmful substances and is compatible with RoHS Directives.
Slider operation is smooth and comfortable.

SPECIFICATIONS

Metric

Order No.	Range	Remarks	Mass
500-776	0 – 150mm	with data output	180g
500-777	0 – 200mm	with data output	210g
500-774	0 – 150mm	w/o data output	180g
500-775	0 – 200mm	w/o data output	210g

Inch/metric

Order No.	Range	Remarks	Mass
500-786	0 – 6″	with data output	180g
500-787	0 – 8″	with data output	210g
500-784	0 – 6″	w/o data output	180g
500-785	0 – 8″	w/o data output	210g

DIMENSIONS

Range	A	B	C	D	H	L
0 – 150mm/0 – 6″	16.5	21	13	40	16	233
0 – 200mm/0 – 8″	20	24.5	16.5	50	16	290

Jaw thickness: 3.5mm

Optional accessories

(Dedicated for the models equipped with a digimatic output function (Code No. 500-776, 500-777, 500-786 and 500-787)) For details, refer to page D-39.

Connecting cables for IT/DP/MUX* 05CZA624: SPC cable with data button (1m) 05CZA625: SPC cable with data button (2m)

USB Input Tool Direct
06ADV380A: SPC cable for USB-ITN-A (2m)

Connecting cables for U-WAVE-T
02AZD790A: SPC cable for U-WAVE with data button (160mm)
02AZE140A: SPC cable for foot switch

* Cannot be used for other than water resistant type Digital calipers with external output function.

About the charge function (SuperCaliper)

The minimum illumination required in the uncharged state is 60lux.
As shown in the table ‘JIS Z 9110 Artificial Illumination Intensity Standard’, this SuperCaliper can be used with confidence in a normal work environment.

The charge function allows the operator to use the SuperCaliper without interrupting work even if the ambient illumination is temporarily insufficient.

In the fully charged state this SuperCaliper can operate for approximately one hour in an environment of 50lux illumination (less than the minimum necessary illumination intensity).
The time necessary for full charge varies according to the charging If the SuperCaliper is left unused in an illumination of 500 lux (usual for manufacturing environments), it takes approximately one hour to reach full charge.

IP67 protection level
Level 6: Dust-proof.
No ingress of dust allowed.
Level 7: Protected against water penetration.
Ingress of water in quantities causing harmful effects shall not be possible when the enclosure is temporarily immersed to a depth of 1 meter in water under standardized conditions of pressure and time (30 min.).

Demonstration device

Technical Data
Resolution: 0.01mm or .0005″/0.01mm Accuracy: ±0.02mm (excluding quantizing error) Repeatability: 0.01mm
Quantizing error: ±1 count Dust/Water protection level: IP67* Power supply: Solar cell**
Display: LCD
Scale type: ABSOLUTE electromagnetic induction linear encoder
Max. response speed: Unlimited
* This model is not waterproof type. Therefore, rustproofing shall be applied after use.
** Can be used continuously above 60lux ambient illumination.

Functions

Origin-set: Absolute origin position can be changed.
Alarm: Error message is displayed and measurement

functions become inoperative if:

Tool is turned on when both illumination and charging voltage are insufficient.
Main unit is extremely polluted and miscalculation occurs in the display unit.

Air leak test equipment for water resistance inspection
Generally, an air leak test is adopted for evaluating water resistance.

Procedure: Place the measuring tool inside the capsule and seal it. Then fill the capsule and the test chamber with air at the required pressure and close the isolating valves. If there is no leak in the measuring tool, the differential pressure sensor will read zero, because the amount of air inside the test chamber is unchanging. However, if there is a leak in the measuring tool, the differential pressure sensor will show a non-zero reading due to a decrease in pressure inside the test chamber as air leaks into the tool. By detecting this differential pressure, GO/NG judgment for the severity of the leak is performed. This air leak test is performed for all ABS coolant proof calipers and coolant proof micrometers.

Air leak test equipment for ABS coolant proof caliper

Large, high contrast dial face
Satin chrome finished line scale
Locking screw above
Measuring surfaces made of steel
Measuring blade for inside measurements
Slide and beam made of hardened stainless steel
Step measuring function
case

Technical data

Order no.	Measuring range mm	Measuring range inches	Graduation value mm	Graduation value inch	Error limit (mm)	Error limit inches	Standard	Friction wheel	Depth Rod
4107005	0 – 150		0.01 mm		0.03 mm		DIN 862	yes	rectangular
4107107	0 – 150		0.02 mm		0.03 mm		DIN 862	yes	rectangular
4107900		0 – 6″		0.001 inch		.0012″	Factory standard	yes	rectangular

To reduce the overall weight the slide and beam are made from aluminum and are coated with a hard anodized surface coating (1100 HV)
Vernier and main scale have a satin chrome finish for glare free reading
Parallax free reading
Locking screw above
Prisma guideway for a more smooth and even movement
Measuring surfaces made of steel
Measuring blades for outside measurements
up to 1000 mm delivered with a case, over 1000 mm individually packed

Technical data

Order no.	Measuring range mm	Readings mm	Error limit (mm)	Standard
4112300	0 – 300	0.02 mm	0.04 mm	Factory standard
4112301	0 – 500	0.02 mm	0.05 mm	Factory standard
4112302	0 – 800	0.02 mm	0.07 mm	Factory standard
4112303	0 – 1000	0.02 mm	0.08 mm	Factory standard
4112304	0 – 1500	0.02 mm	0.16 mm	Factory standard
4112305	0 – 2000	0.02 mm	0.16 mm	Factory standard

With fine adjustment
Measuring blades for outside measurements
Vernier and main scale have a satin chrome finish for glare free reading
Locking screw above
Rounded measuring blades for inside measurements
Measuring surfaces made of steel
Slide and beam made of hardened stainless steel
Raised guideway for the protection of the scale
case

Technical data

Order no.	Measuring range mm	Readings mm	Error limit (mm)	Standard
4113300	0 – 200	0.02 mm	0.05 mm	Factory standard
4113301	0 – 300	0.02 mm	0.05 mm	Factory standard
4113302	0 – 500	0.02 mm	0.06 mm	Factory standard
4113303	0 – 800	0.02 mm	0.08 mm	Factory standard
4113304	0 – 1000	0.02 mm	0.08 mm	Factory standard

Measuring blades for outside measurements
Vernier and main scale have a satin chrome finish for glare free reading
Locking screw above
Rounded measuring blades for inside measurements
Measuring surfaces of workshop caliper made of steel
Slide and beam made of hardened stainless steel
Raised guideway for the protection of the scale
up to 1000 mm delivered with a case, over 1000 mm individually packed

Technical data of Workshop caliper

Order no.	Measuring range mm	Readings mm	Error limit (mm)	Standard
4113200	0 – 200	0.05 mm	0.05 mm	DIN 862
4113201	0 – 300	0.05 mm	0.05 mm	DIN 862
4113202	0 – 500	0.05 mm	0.07 mm	DIN 862
4113203	0 – 800	0.05 mm	0.1 mm	DIN 862
4113204	0 – 1000	0.05 mm	0.12 mm	DIN 862
4113205	0 – 1500	0.05 mm	0.18 mm	DIN 862
4113206	0 – 2000	0.05 mm	0.22 mm	DIN 862

MARCAL 18 N WORKSHOP VERNIER CALIPERS

Vernier and main scale have a satin chrome finish for glare free reading
Locking screw above
Rounded measuring blades for inside measurements
Measuring surfaces made of steel
Slide and beam made of hardened stainless steel
Raised guideway for the protection of the scale
up to 1000 mm delivered with a case, over 1000 mm individually packed

Technical data

Order no.	Measuring range mm	Readings mm	Error limit (mm)	Standard
4112200	0 – 200	0.02 mm	0.05 mm	Factory standard
4112201	0 – 300	0.02 mm	0.05 mm	Factory standard
4112210	0 – 500	0.05 mm	0.07 mm	DIN 862
4112211	0 – 800	0.05 mm	0.1 mm	DIN 862
4112212	0 – 1000	0.05 mm	0.12 mm	DIN 862
4112213	0 – 1500	0.05 mm	0.18 mm	DIN 862
4112214	0 – 2000	0.05 mm	0.22 mm	DIN 862

MARCAL 18 N WORKSHOP VERNIER CALIPERS

Measuring blades for outside measurements
High contrast analog display
Locking screw above
Rounded measuring blades for inside measurements
Slide and beam made of hardened stainless steel
Immediate measurements due to the Reference System
Raised guideway for the protection of the scale
Excellent resistance against dust, coolants and lubricants
Dirt wipers are integrated in the slide
up to 1000 mm delivered with a case, over 1000 mm individually packed

Technical data

Order no.	Measuring range mm	Measuring range inches	Readings mm	Vernier value inch	Error limit (mm)	Error limit inches	Standard
4112220	0 – 300		0.02 mm		0.05 mm		Factory standard
4112221	0 – 500		0.02 mm		0.06 mm		Factory standard
4112222	0 – 800		0.02 mm		0.08 mm		Factory standard
4112223	0 – 1000		0.02 mm		0.08 mm		Factory standard
4112224	0 – 1500		0.02 mm		0.1 mm		Factory standard
4112225	0 – 2000		0.02 mm		0.12 mm		Factory standard
4112230	0 – 300	0 – 12″	0.02 mm	.001″	0.05 mm	.002″	Factory standard
4112231	0 – 500	0 – 20″	0.02 mm	.001″	0.06 mm	.0025″	Factory standard
4112232	0 – 800	0 – 32″	0.02 mm	.001″	0.08 mm	.003″	Factory standard
4112233	0 – 1000	0 – 40″	0.02 mm	.001″	0.08 mm	.003″	Factory standard
4112234	0 – 1500	0 – 60″	0.02 mm	.001″	0.1 mm	.004″	Factory standard
4112235	0 – 2000	0 – 80″	0.02 mm	.001″	0.12 mm	.005″	Factory standard

Vernier and main scale have a satin chrome finish for glare free reading
Thumb clamp
Measuring surfaces made of steel
Measuring blade for inside measurements
Slide and beam made of hardened stainless steel
Step measuring function
Raised guideway for the protection of the scale
thread table
case

Technical data

Order no.	Measuring range mm	Measuring range inches	Readings mm	Vernier value inch	Error limit (mm)	Error limit inches	Standard	Depth Rod
4100600	0 – 150	0 – 6″	0.05 mm	1/128″	0.05 mm	.002″	DIN 862	rectangular